Categories: Antenna Plans

Building 5 Elements UHF Yagi (Panda Antenna Build)

5 Elements Yagi UHF (Panda Antenna Build)

Material list for building a 5 Elements UHF Yagi

1. 1″ X 0.5″ Rectangular Aluminum tubing for the boom
2. 3/8″ Aluminum tubing for antenna elements
3. 1cm Outside diameter antenna tubing for elements holder
4. 1pc SO239 connector
5. Pop rivets / Rivet tool
6. #12 AWG Copper wire with insulation (12″for Gamma match)
7. Soldering iron
8. 10pcs Stainless steel nuts and bolts 20mm length 3mm diameter
9. 1pc, Butterfly nut and 1 bolt 18mm length 3mm diameter
10. Aluminum plate 0.5mm thickness
11. Collapsible tube (shrinkable tubes)

Download Yagi Dimensions Here

To build the 5 Elements UHF Yagi you may follow the direction for building the 3 Elements Yagi. The elements for UHF antenna are shorter and it needs more precise cutting. Follow the measurements on the diagram including spacing between the elements and when built successfully it will give you a very desirable 11 dBi gain or about or about 8.85dBd.

To increase the performance you may also configure the antenna in stack configuration by making two antenna’s and connect it with a phasing harness for increased performance.

Antenna Gain Simulation and Signal Pattern Using 4Nec2 antenna modeling for individual antenna.

Front to Back Ratio: 9.92dB
Antenna Gain: 10.98 ~ 11dBi
Beamwitdh: 56° Vertical 46° Horizontal

Vertical Pattern 5 Elements UHF Yagi

Horizontal Pattern 5 Elements UHF Yagi

Combined Pattern Free Space

Combined Pattern Ground Effect

Ephraim Gariguez

View Comments

  • Hello Sir,
    Congratulations for your work. From all designs which I saw on the internet I have build this antenna according to your specifications. It's the best I saw until now and I'm happy with it.
    Unfortunately I don't have a SWR or VNA so I have a short question. It's there a "middle" position for the shorting stub where I can used the antenna without measurement. Thank you. I wish you good luck. YO6OPD, 73 !

    • Using an antenna analyzer or SWR meter is still best to check your antenna SWR. In the absence of those the initial tuning position is exactly halfway to the gamma match. Assuming that you follow all the measurements you can easily obtain an SWR of 1.5:1 with the antenna, but it is still best to recheck it with an SWR meter or an antenna analyzer.

  • Hi. I am EA7AWC and My QRA is: Manuel and I am setting up your Yagi antenna design. Please can you give more details to build the impedance adapter (Gamma match). Tube dimensions, distance to the radiator dipole element, I think it uses a piece of coaxial cable. Thank you

Recent Posts

Can’t change SSH port Armbian 24.5.1 Bookworm Linux 6.6.31 current-sunxi – Fixed

I'm on Orange Pi One Armbian 24.5.1 Bookworm with Linux 6.6.31-current-sunxi I found a fix…

3 weeks ago

Realtek RTL8111/8168/8411 PCIe GBE NIC – dissapear unusable after Kernel 6.9 update from 6.8 PopOS! work around…

I've been using Linux PopOS for a year now on my old Samsung RF411 notebook…

4 weeks ago

Logitech RF mouse suddenly stop scrolling on Ubuntu 22.04LTS

Note: This procedure is also tested to work with Pop!_OS 22.04 LTS I have an…

3 months ago

Zastone Radios Software

The following are software for radios by Zastone Technology this is publicly and freely available…

6 months ago

PHP 8.2 FPM Tuning

This is a personal note for myself to remember the process I used to tune…

6 months ago

Kicad 6.0 Fix or Workaround for OpenGL required version 1.5

Kicad 6.0 is an schematic entry and pcb layout editor software that is popularly used…

2 years ago